Micromod MOD: Modcell 2050R Users Guide Manual de usuario Pagina 218
- Pagina / 228
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
IB-23C650
CALIBRATION DATA
Table 15. Main/Option Board Calibration (Base Configuration Menu)
Step Step Description
Top
Display
17.3
Input 2 Ma. Resistance Ratio
UP
begins entry at most significant digit. Use
UP
or
DN
to set the digit, then
SCRL
to scroll to the
next digit. Repeat for all digits.
SCRL
advances to:
Step 17.3.1 if value was changed.
Step 17.4 otherwise.
INPUT 2
17.3.1
Are You Sure You Want to Change Input 2 Ma.
Res. Ratio?
UP
selects YES or
DN
selects NO.
SCRL
advances to:
Step 17.3 on NO. Step 17.4 on YES.
ARE YOU
17.4
Input 2 Circuit Compensation
UP
begins entry at most significant digit. Use
UP
or
DN
to set the digit, then
SCRL
to scroll to the
next digit. Repeat for all digits.
SCRL
advances to:
Step 17.4.1 if value was changed.
Step 17.5 otherwise.
INPUT 2
17.4.1
Are You Sure You Want to Change Process
Input Circuit Compensation?
UP
selects YES or
DN
selects NO.
SCRL
advances to:
Step 17.4 on NO. Step 17.5 on YES.
ARE YOU
17.5
Output 2 Current Ratio
UP
begins entry at most significant digit. Use
UP
or
DN
to set the digit, then
SCRL
to scroll to the
next digit. Repeat for all digits.
SCRL
advances to:
Step 17.5.1 if value was changed. Step 18 in
BASE CFG MENU otherwise.
OUTPUT 2
17.5.1
Are You Sure You Want to Change Output 2
Current Ratio?
UP
selects YES or
DN
selects NO.
SCRL
advances to:
Step 17.5 on NO. Step 18, Default Database
entry point, in BASE CFG MENU on YES.
ARE YOU
212
- User’s Guide 1
- MicroMod Automation, Inc 2
- CONTENTS 3
- CONTENTS (Cont’d) 4
- ILLUSTRATIONS 5
- ILLUSTRATIONS (Cont’d) 6
- IDENTIFICATION INFORMATION 8
- IB-23C650 10
- INTRODUCTION 10
- INSTALLATION 11
- MOUNTING 13
- WIRING GUIDELINES 14
- S-3017-7A(3) 15
- POWER CONNECTIONS 16
- GROUND CONNECTIONS 17
- Electrical Noise 17
- REMOTE SET-POINT CONNECTIONS 18
- RTD INPUT 21
- VOLT INPUT 24
- MILLIVOLT INPUT 25
- DIGITAL INPUT 26
- Minimum Resistance: 27
- No External Parts: 500 ohms 27
- OUTPUT SIGNAL CONNECTIONS 28
- Receiver 30
- Precision Dropping Resistor 30
- Maximum Value: 400 ohms 30
- Blank Page 32
- GENERAL PREPARATIONS 33
- SETUP FUNCTIONS 34
- SETUP METHOD 34
- SETUP CONTROLS 34
- DATA BASE REFERENCE TABLES 34
- to advance to Step 3.5 54
- Table 2. Input Setup Menu 55
- to advance to Step 4.7 60
- (i. e. ,100% = 20 mA dc) 79
- Table 6. RS-485 Setup Menu 86
- Table 8. Set-Point Setup Menu 93
- to advance to Step 7 98
- to return to Step 1 98
- to advance to Step 7.10.8 108
- (Step 3 or 4) 109
- Table 11. Alarm Settings Menu 115
- Table 12. Tune Menu 121
- BASIC OPERATION 129
- CONTROL KEYS 131
- ENGINEERING DISPLAYS 132
- STATUS DISPLAYS 133
- Top & Middle 135
- BAR GRAPHS 136
- ALARM INDICATOR 136
- . If diagnostic 137
- OPERATION IN AUTOMATIC MODE 138
- AUTO/MANUAL TRANSFER 142
- OPERATION IN MANUAL 144
- Enabling Digital Inputs 149
- One Digital Input 151
- CONTROL OUTPUT LIMITING 152
- Alarm Messages 155
- Alarm Trip Points 155
- Alarm Priority 155
- Beep on Alarm Occurrence 155
- Alarms with Acknowledgment 155
- Alarm Type Messages 156
- MANUAL TUNING 159
- key to set 160
- I = P (Minutes) 161
- AUTOMATIC TUNING 163
- Setup Procedure 163
- Table 13. Autotune Procedure 167
- STEP SIZ (Step 5) 168
- Table 13. Autotune Procedure 169
- to advance to: 170
- RAMP/SOAK OPERATION 175
- OPERATION IN AUTOMATIC 177
- CONTROLLING RAMP/SOAK PROFILE 179
- Ramp or Soak Hysteresis 181
- Ramp/Soak Hold 181
- TOTALIZER OPERATION 183
- Totalizer Status Display 184
- Totalizer Reset Display 184
- Preset Value 185
- Predetermined Count 185
- RATIO BIAS CONTROL 189
- Control Method 190
- Ratio Function 190
- Bias Function 191
- A/M RATIO BIAS STATION 193
- Instrument Set-up 195
- A/M Switching 195
- TIME PROPORTIONING CONTROL 197
- S-1107-41B 198
- CURRENT PROPORTIONING CONTROL 199
- DESCRIPTION 201
- S-1107-248A 202
- S-1107-52A 202
- ON/OFF CONTROL 203
- DIAGNOSTICS 207
- Input Failure Messages 208
- Operational Failure Messages 208
- TROUBLESHOOTING 209
- Problem Possible Cause Action 210
- CALIBRATION DATA 211
- MAINTENANCE 220
- RECORD OF DATABASE 221
Relacionado con productos y manuales para Equipo Micromod MOD: Modcell 2050R Users Guide
(38 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales