Micromod MOD: Modcell 2050R Users Guide Manual de usuario Pagina 134
- Pagina / 228
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
IB-23C650
BASIC OPERATION
MIDDLE DISPLAY
Remote: Set-point is derived from a remote location and
is brought into the instrument through the
remote set-point input on the option card.
Local: Set-point is derived at the instrument and may
be fixed in the SETPTS MENU or adjusted in
the DISPLAYS MENU.
Local 2: Local set-point number 2 is derived at the
instrument and may be fixed in the SETPTS
MENU or adjusted in the DISPLAYS MENU.
Local 3: Local set-point number 3 is derived at the
instrument and may be fixed in the SETPTS
MENU or adjusted in the DISPLAYS MENU.
Local 4: Local set-point number 4 is derived at the
instrument and may be fixed in the SETPTS
MENU or adjusted in the DISPLAYS MENU.
Ramp/ Ramp/soak profile has been enabled in
Soak: the BASE CFG MENU and is active. See
operation of Ramp/Soak.
Ramp/ Ramp/soak profile has been enabled in
Soak the BASE CFG MENU and is in the hold
Hold: state. [RSH] intermittently flashes with [LOC].
See operation of Ramp/Soak.
BOTTOM DISPLAY
Output: Controller output in percent is being shown in
the lower engineering display.
Set-Point: The controller’s active set-point value is being
shown in the lower engineering display.
Balance: An imbalance exists between the active set-
point and the newly selected set-point. See
Automatic Operation with Remote or Multiple
Set-Points.
128
- User’s Guide 1
- MicroMod Automation, Inc 2
- CONTENTS 3
- CONTENTS (Cont’d) 4
- ILLUSTRATIONS 5
- ILLUSTRATIONS (Cont’d) 6
- IDENTIFICATION INFORMATION 8
- IB-23C650 10
- INTRODUCTION 10
- INSTALLATION 11
- MOUNTING 13
- WIRING GUIDELINES 14
- S-3017-7A(3) 15
- POWER CONNECTIONS 16
- GROUND CONNECTIONS 17
- Electrical Noise 17
- REMOTE SET-POINT CONNECTIONS 18
- RTD INPUT 21
- VOLT INPUT 24
- MILLIVOLT INPUT 25
- DIGITAL INPUT 26
- Minimum Resistance: 27
- No External Parts: 500 ohms 27
- OUTPUT SIGNAL CONNECTIONS 28
- Receiver 30
- Precision Dropping Resistor 30
- Maximum Value: 400 ohms 30
- Blank Page 32
- GENERAL PREPARATIONS 33
- SETUP FUNCTIONS 34
- SETUP METHOD 34
- SETUP CONTROLS 34
- DATA BASE REFERENCE TABLES 34
- to advance to Step 3.5 54
- Table 2. Input Setup Menu 55
- to advance to Step 4.7 60
- (i. e. ,100% = 20 mA dc) 79
- Table 6. RS-485 Setup Menu 86
- Table 8. Set-Point Setup Menu 93
- to advance to Step 7 98
- to return to Step 1 98
- to advance to Step 7.10.8 108
- (Step 3 or 4) 109
- Table 11. Alarm Settings Menu 115
- Table 12. Tune Menu 121
- BASIC OPERATION 129
- CONTROL KEYS 131
- ENGINEERING DISPLAYS 132
- STATUS DISPLAYS 133
- Top & Middle 135
- BAR GRAPHS 136
- ALARM INDICATOR 136
- . If diagnostic 137
- OPERATION IN AUTOMATIC MODE 138
- AUTO/MANUAL TRANSFER 142
- OPERATION IN MANUAL 144
- Enabling Digital Inputs 149
- One Digital Input 151
- CONTROL OUTPUT LIMITING 152
- Alarm Messages 155
- Alarm Trip Points 155
- Alarm Priority 155
- Beep on Alarm Occurrence 155
- Alarms with Acknowledgment 155
- Alarm Type Messages 156
- MANUAL TUNING 159
- key to set 160
- I = P (Minutes) 161
- AUTOMATIC TUNING 163
- Setup Procedure 163
- Table 13. Autotune Procedure 167
- STEP SIZ (Step 5) 168
- Table 13. Autotune Procedure 169
- to advance to: 170
- RAMP/SOAK OPERATION 175
- OPERATION IN AUTOMATIC 177
- CONTROLLING RAMP/SOAK PROFILE 179
- Ramp or Soak Hysteresis 181
- Ramp/Soak Hold 181
- TOTALIZER OPERATION 183
- Totalizer Status Display 184
- Totalizer Reset Display 184
- Preset Value 185
- Predetermined Count 185
- RATIO BIAS CONTROL 189
- Control Method 190
- Ratio Function 190
- Bias Function 191
- A/M RATIO BIAS STATION 193
- Instrument Set-up 195
- A/M Switching 195
- TIME PROPORTIONING CONTROL 197
- S-1107-41B 198
- CURRENT PROPORTIONING CONTROL 199
- DESCRIPTION 201
- S-1107-248A 202
- S-1107-52A 202
- ON/OFF CONTROL 203
- DIAGNOSTICS 207
- Input Failure Messages 208
- Operational Failure Messages 208
- TROUBLESHOOTING 209
- Problem Possible Cause Action 210
- CALIBRATION DATA 211
- MAINTENANCE 220
- RECORD OF DATABASE 221
Relacionado con productos y manuales para Equipo Micromod MOD: Modcell 2050R Users Guide
(38 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales