Micromod MOD: 30ML Operation and Template Setup Manual de usuario descargar pdf (Pagina 26)

MOD 30ML Operation

SETUP

2-16

Table 8. User Compound Template Configuration (Cont’d)

Step Step Description Line 1 Line 2 Line 6 Entry Description

Millivolt and Thermocouple Inputs Only:

8D14

(TC)

Process Input CJC Source

∇ ∆ change value, ENT enters

NXT, PRV change step

PROC INP CJC SRC NONE

NONE, BI AIN 1, S01 TO S11

8D15

(TC)

Process Input Burnout

∇ ∆ change value, ENT enters

NXT, PRV change step

PROC INP BURNOUT NONE

NONE - no burnout detection

DN SCALE - signal moves

downscale if burnout is detected.

UP SCALE. - signal moves upscale

if burnout is detected.

All Inputs:

8D16 Process Input Low Quality

∇ ∆ change value, ENT enters

NXT, PRV change step

PROC INP LO QUAL -10.0

Result is set BAD if it goes below

this value.

8D17 Process Input High Quality

∇ ∆ change value, ENT enters

NXT, PRV change step

PROC INP HI QUAL 110.000

Result is set BAD if it goes above

this value. High quality must be

higher than the low quality value.

8D18 Process Input Quality Alarm

∇ ∆ change value, ENT enters

NXT, PRV change step

PROC INP QUAL ALM DISABLE

Disable or Enable.

8D19 Process Input Quality Digital Output

∇ ∆ change value, ENT enters

NXT, PRV change step

PROC INP QA D OUT NONE

NONE or S01 to S11 location of

digital output module.

8D20 Process Input Quality Priority

∇ ∆ change value, ENT enters

NXT, PRV change step

PROC INP QA PRI 1

0 = suppress unacknowledge

1 to 255 = priority level.

8D21 Process Input (Exit)

∆ moves up to Step 8D

NXT, PRV change step

PROC INP

8E Setpoint (Entry)

∇ moves down to Step 8E1

NXT, PRV change step

CTAG01 SETPT

8E1 Setpoint Display Format

∇ ∆ change value, ENT enters

NXT, PRV change step

SETPOINT DISP FMT FLOAT 3

Float 0 = x

Float 1 = x.x

Float 2 = x.xx and so forth to

Float 6 = x.xxxxxx

8E2 Remote Setpoint Input Setup (Entry)

∇ moves down to Step 8E2A

NXT, PRV change step

REMOTE SETPOINT

8E2A Remote Setpoint Slot Position

∇ ∆ change value, ENT enters

NXT, PRV change step

REMSETPT SLOT NONE

None, BI AIN 1, BI AIN 2, S01 to

S11

8E2B Remote Setpoint Input Type

∇ ∆ change value, ENT enters

NXT, PRV change step

REMSETPT INP TYPE VOLTS

Select type as: VOLTS, MVOLTS,

CURRENT, RESIST, THRMOCPL

1 Slot: RTD2WIRE, CURRNT2W

2 Slots: RTD3WIRE, WIDERES

Built-in only: TC W/CJC, RTD

8E2C Remote Setpoint Input Setup

Same as process value inputs.

See Process Value input setup.

8E2D Remote Setpoint Input Setup (Exit)

∆ moves up to Step 8E2

NXT, PRV change step

REMSETPT

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 83 84

Comentarios a estos manuales

Sin comentarios

Micromod MOD: 30ML Operation and Template Setup Manual de usuario Pagina 26

Comentarios a estos manuales

Relacionado con productos y manuales para Equipo Micromod MOD: 30ML Operation and Template Setup