Micromod MOD: 1800P - MOD 30ML Identity Module (Version 2) Manual de usuario Pagina 34
- Pagina / 70
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Continuous Control Functions
PID CONTROL BLOCK
2-28
70
Setpoint Mode Restart Value
(SPMRV) ........................................................................... CWR
The setpoint mode restart value is used when the instrument is initialized due to a cold of
frozen restart. Restart mode values must not conflict with the allowed modes value.
LOCAL 0 The setpoint mode restart value is LOCAL.
REMOTE 1 The setpoint mode restart value is REMOTE.
PREVIOUS 4 The setpoint mode restart value is PREVIOUS.
71
Output Mode Restart Value
(OPMRV) ............................................................................. CWR
The output mode restart value is used when the instrument is initialized due to a cold or frozen
restart. Restart mode values must not conflict with the allowed modes value. The user cannot
set this value when mode model is CTRL MODE.
MANUAL 0 Manual value is used. Value is set to MANUAL when the configurator
is used to change mode model to CTRL MODE.
AUTO 1 Auto value is used.
PREVIOUS 4 Previous value is used.
72
Control Mode Restart Value
(CMRV)............................................................................... CWR
The control mode restart value is used when the instrument is initialized due to a cold or
frozen restart. Restart mode values must not conflict with the allowed modes value. The user
cannot set this value when mode model is SP/OP.
MANUAL 0 The control mode restart value is MANUAL. Value is set to MANUAL
when the configurator is used to change mode model to CTRL
MODE.
AUTO 1 The control mode restart value is AUTO.
CASCADE 2 The control mode restart value is CASCADE.
PREVIOUS 4 The control mode restart value is PREVIOUS.
N/A 15 Configurator entry when setting mode model to SP/OP MODE only.
75
Process Variable Input
(PVI) ............................................................................................ CWR
The process variable input is a floating-point value that is the process source of the control
loop.
value Fixed floating point value is Process Variable Input value.
LSP Any floating-point variable is Process Variable Input value.
76
Dead Time Compensation Input
(DTCI) .......................................................................... CWR
The dead time compensation input adds a compensation signal to the process variable input.
This floating-point value is added before normalization.
NONE Attribute is not configured into the database.
value Fixed floating point value is Dead Time Compensation Input value.
LSP Any floating-point variable is Dead Time Compensation Input value.
- Data Base Reference 1
- MicroMod Automation, Inc 2
- CONTENTS 3
- ILLUSTRATIONS 4
- INTRODUCTION 5
- 1.4 RELATED DOCUMENTATION 6
- 1.5 VERSION IDENTIFICATION 6
- 2.1 GENERAL 7
- 2.2 PID CONTROL BLOCK (PID) 8
- PID Controller Block 9
- Continuous Control Functions 10
- PID CONTROL BLOCK 10
- OPCERRUQ 17
- OPCERRAQ 17
- Attribute 18
- Control Algorithm Type 30
- Manual Reset Balance Type 31
- Gain Base Value 31
- Reset Rate Base Value 31
- Preact Time Base Value 32
- Manual Reset Initial Value 32
- Manual Reset Quality 32
- Control Modes Allowed 32
- Control Mode 33
- Control Mode Status Quality 33
- Control Mode Command 33
- Setpoint Mode Restart Value 34
- Output Mode Restart Value 34
- Control Mode Restart Value 34
- Process Variable Input 34
- Dead Time Compensation Input 34
- Gain Modifier 36
- Reset Rate Modifier 36
- Preact Time Modifier 36
- Remote Setpoint Bias Input 36
- Mode Model 38
- Input Filter Type 38
- Input Filter Time Constant 39
- 2.2.4 PID Block Events 40
- RAMP SOAK BLOCK (RSK) 41
- DATA BASE PARAMETERS 41
- RAMP SOAK BLOCK 42
- 3.3 RSK BLOCK PARAMETERS 45
- Block Length 50
- Result Quality 53
- State A Quality 53
- State B Quality 53
- State C Quality 53
- Cycle Number Quality 55
- Mode Quality 55
- 3.5 RAMP/SOAK BLOCK EVENTS 60
- APPENDIX A 61
- PID BLOCK CROSS REFERENCE 61
Relacionado con productos y manuales para Equipo Micromod MOD: 1800P - MOD 30ML Identity Module (Version 2)
(24 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales