Micromod MOD: 1800P - MOD 30ML Identity Module (Version 2) Manual de usuario Pagina 17
- Pagina / 70
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Continuous Control Functions
PID CONTROL BLOCK
2-11
Error Checks
If a calculation error occurs in the PID calculation, and the set qualities bad attribute is TRUE,
then the output qualities (output and track status) are set BAD. The PID calculation will be
initialized when qualities become good again.
In a cycle where the PID outputs have been previously marked BAD, but can now be
successfully calculated (required inputs are good), and the controller mode is AUTO or
CASCADE, the PID algorithm will initialize using the present output value. It is recommended
that the application design provide logic ’downstream’ of the PID block to set a track signal
when the PID qualities go bad. This way, the PID block will initialize from the track value
when it is again capable of executing, which would most likely be the preferred method of
initialization.
2.2.2 PID Control Block Parameters
The mnemonics, valid values, and data types for all fields that may be selected for display
and/or be used in making softwiring connections are listed in Table 2-1. The following further
defines the PID Control block configuration parameters.
Block Type
PID This is the PID Control block type and is configured on the Function
Block Selection page.
Occurrence
1 to 4096 There may be up to 4096 ‘instances’ allowed of the PID block type.
Table 2-1. PID Control Block Attributes, Valid Values, Mnemonics, and Data Types
Field Name /
Attribute
Mnemonic Valid Values CWR Data Type Attr
Version VERSION 1 – – R Long State 00
Block Length BLKLEN – – R Count 01
Block State
STATE RUN, HOLD, OFF, DEBUG CWR Short State 02
Bad Inputs Accepted
BADINP NO(0), YES(1) CWR Discrete 03
Diagnostic Group
SUPPGRP NONE, 1, 2, 3, 4, 5, 6, 7 CWR Long State 04
Calculation Error
CERRS ENABLE(0), SUPPRESS(1) CWR Discrete 05
Calc. Error Unacked CERRU NO(0), YES(1) – WR Discrete 06
Calc. Error Unacked Quality CERRUQ GOOD(0), BAD(1) – WR Discrete 07
Calc. Error Active CERRA NO(0), YES(1) – WR Discrete 08
Calc. Error Active Quality CERRAQ GOOD(0), BAD(1) – WR Discrete 09
Output Calculation Error
OPCERRS ENABLE(0), SUPPRESS(1) CWR Discrete 10
Output Calc. Error Unacked OPCERRU NO(0), YES(1) – WR Discrete 11
Output Calc. Error Unacked Q
OPCERRUQ
GOOD(0), BAD(1) – WR Discrete 12
Output Calc. Error Active OPCERRA NO(0), YES(1) – WR Discrete 13
Output Calc. Error Active Q
OPCERRAQ
GOOD(0), BAD(1) – WR Discrete 14
Control Interval
CI Msec Time Value CWR Msec Time 15
Setpoint Modes Allowed
SPMA L(1), R(2), L.R(3) C – R Count 16
Setpoint Mode Status,
Initial Value
SPMS LOCAL(0), REMOTE(1),
TRACK
(3)*,
FAULT
(5)*
CWR Short State 17
Setpoint Mode Status Quality SPMSQ GOOD(0), BAD(1) – WR Discrete 18
Setpoint Mode Command SPMC LOCAL(0), REMOTE(1) – – R Short State 19
Setpoint Track Enable
SPTE NO(0), YES(1) C – R Discrete 20
- Data Base Reference 1
- MicroMod Automation, Inc 2
- CONTENTS 3
- ILLUSTRATIONS 4
- INTRODUCTION 5
- 1.4 RELATED DOCUMENTATION 6
- 1.5 VERSION IDENTIFICATION 6
- 2.1 GENERAL 7
- 2.2 PID CONTROL BLOCK (PID) 8
- PID Controller Block 9
- Continuous Control Functions 10
- PID CONTROL BLOCK 10
- OPCERRUQ 17
- OPCERRAQ 17
- Attribute 18
- Control Algorithm Type 30
- Manual Reset Balance Type 31
- Gain Base Value 31
- Reset Rate Base Value 31
- Preact Time Base Value 32
- Manual Reset Initial Value 32
- Manual Reset Quality 32
- Control Modes Allowed 32
- Control Mode 33
- Control Mode Status Quality 33
- Control Mode Command 33
- Setpoint Mode Restart Value 34
- Output Mode Restart Value 34
- Control Mode Restart Value 34
- Process Variable Input 34
- Dead Time Compensation Input 34
- Gain Modifier 36
- Reset Rate Modifier 36
- Preact Time Modifier 36
- Remote Setpoint Bias Input 36
- Mode Model 38
- Input Filter Type 38
- Input Filter Time Constant 39
- 2.2.4 PID Block Events 40
- RAMP SOAK BLOCK (RSK) 41
- DATA BASE PARAMETERS 41
- RAMP SOAK BLOCK 42
- 3.3 RSK BLOCK PARAMETERS 45
- Block Length 50
- Result Quality 53
- State A Quality 53
- State B Quality 53
- State C Quality 53
- Cycle Number Quality 55
- Mode Quality 55
- 3.5 RAMP/SOAK BLOCK EVENTS 60
- APPENDIX A 61
- PID BLOCK CROSS REFERENCE 61
Relacionado con productos y manuales para Equipo Micromod MOD: 1800P - MOD 30ML Identity Module (Version 2)
(24 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.022 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales