Micromod Micro-DCI: 53SL5100A Single Loop Controller Manual de usuario Pagina 59
- Pagina / 152
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Single Loop Process Controller Instruction Manual
Configuration Parameters 51
Controller
Span
■
● ▲ ◆ C115 100
These two parameters set the upper and
lower values on the controller display. They
permit the control action to be defined over a
range independent of the process variable
input range. They also determine the speed
at which the setpoint changes when the up or
down arrow pushbuttons are pressed (CS1
thiough CS3). For CS4, they determine only
the displayable range, as the setpoint
pushbuttons are not used.
Controller
Lower Range
■
● ▲ ◆ C116 0
Control Tag
Name
■
● ▲ ◆ A000 CON0
This is an assignable 10 character name that
appears with CS1-4 displays.
Engineering
Units
■
● ▲ ◆ A001 Percent
The default is PERCENT, but is assignable
as units of measure the Process Variable
represents.
Note: CS1 = Single Loop (PID) Controller, CS2 = Analog Backup Controller, CS3 = Ratio Controller, and
CS4 = Automatic/Manual Station.
Table 4-9. Parameter Display Module
Title Symbol PAR1 Default Attribute
Purpose: This module provides quick pushbutton display access to any three selected datapoints
(e.g., Alarm Limits 1 & 2 and Alarm Dead Band) without the necessity of entering Engineering mode
and addressing the datapoints.
Title
PTAG A014 CON-0
TUNE
This is an assignable in character name that
appears with the parameter display.
Point 1 Name
PNA A015 PROP.
BAND
This is an assignable 10 character name for the
Point 1 Designator.
Point 2 Name
PNB A016 RESET
This is an assignable 10 character name for the
Point 2 Designator.
Point 3 Name
PNC A017 RATE
It is an assignable 10 character name for the
Point 3 Designator.
Point 1
Designator
PDA F087 C106
value
A database datapoint whose contents will be
displayed under the Point 1 Name (e.g., C103 to
display the Alarm Limit 1 setting).
Point 2
Designator
PDB F088 C107
value
A database datapoint whose contents will be
displayed under the Point 2 Name (e.g., C104 to
display the Alarm Limit 2 setting).
Table 4-8. Controller Module (CON-0) (Continued)
Title Symbol
CS
■ ● ▲ ◆
1 | 2 | 3 | 4
CON-0
Datapoint
Default Attribute
- INSTRUCTION MANUAL 1
- MicroMod Automation, Inc 2
- TABLE OF CONTENTS 3
- LIST OF FIGURES 6
- LIST OF TABLES 7
- 1.0 Introduction 9
- Introduction 3 11
- 1.2 Model Number Breakdown 12
- 1.3 Specifications 13
- 2.0 Installation 17
- Installation 11 19
- Figure 2-3. Intercase Spacing 20
- 2.4 Connections 21
- 2.5 Grounding 23
- 16 Installation 24
- Installation 17 25
- 18 Installation 26
- 3.0 Front Panel 27
- Front Panel 21 29
- Figure 3-6. Alarm Overlay 30
- 3.3 Front Panel Pushbuttons 31
- 24 Front Panel 32
- 3.3.1 Displaying a Datapoint 36
- 3.3.2 Altering a Datapoint 37
- ∆ = space 38
- 3.3.3 Defaulting the Database 39
- Figure 3-14. The KEY? Prompt 42
- Front Panel 35 43
- C & H 45
- A & Q 45
- TRL-C aborts the operation 46
- 40 Front Panel 48
- 4.0 Configuration Parameters 49
- Figure 4-1. ANIO/1 53
- Figure 4-2 53
- Figure 4-3. CCI0 55
- Figure 4-4. CCO0 55
- CCO L024 0 56
- OINV L288 0 56
- COTAG A280 CCO0 56
- AIX ■ ● ▲ ◆ B335 1 57
- RSW ■ ● ▲ ◆ L106 1 57
- Table 4-11. System Module 61
- Table 5-8. System Module 71
- 6.0 Analog Backup Controller 73
- Table 6-1 75
- Table 6-8. System Module 81
- 7.0 Ratio (PID) Controller 83
- Table 7-1 85
- Table 7-7. System Module 91
- 8.0 Automatic/Manual Station 93
- Table 8-1 95
- Table 8-8. System Module 101
- 9.0 Parameter Display 103
- 96 Parameter Display 104
- 98 Parameter Display 106
- 10.0 Instrument Tuning 107
- 10.3 Derivative Action (TD) 108
- 10.4 Instrument Tuning 108
- 11.0 EASY-TUNE 111
- 11.3 EASY-TUNE Parameters 112
- 108 Easy-Tune 116
- 110 Easy-Tune 118
- 112 Easy-Tune 120
- 12.0 Maintenance 121
- 12.3 Calibration 122
- 12.5 Resetting the Controller 123
- 12.6 Parts List 124
- 12.7 Supplemental Information 124
- Maintenance 117 125
- 118 Maintenance 126
- Maintenance 119 127
- 120 Maintenance 128
- Appendix B: Communications 133
- B.1.1 Configuration 134
- B.1.2 Protocol 135
- B.1.3 Message Types 136
- B 200H 1 138
- L 500H 1 Bit 138
- C 600H 3 138
- Appendix C: Database 141
- Table C-2. Database 142
- CIZ B264 144
- AIX B335 1 145
- ANO0 C000 0 145
- PV C100 0 145
- P or DOWN arrow pushbuttons 146
- 142 Database 150
Relacionado con productos y manuales para Equipo Micromod Micro-DCI: 53SL5100A Single Loop Controller
(180 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales