Micromod Micro-DCI: 53SL5100A Single Loop Controller Manual de usuario Pagina 148
- Pagina / 152
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Single Loop Process Controller Instruction Manual
140 Database
Auto Status
AUT
L107 0
It indicates the Auto/Manual state of the controller. It is
the logical AND of the Auto Switch (L112) and Auto
Enable (L114). A 1 for this bit indicates auto; a 0 for this
bit indicates manual.
Remote
Status
RMT L108 0
It indicates the Remote/Local setpoint source for the
controller. It is the logical AND of the Remote Enable
(L115) and the Remote Switch (L113). A 1 for this bit
indicates remote; a 0 for this bit indicates local.
Reverse
Valve
RSV L109 0
This parameter provides information for the various
control displays to indicate which direction the control
output must go to close the final control element. A 1
indicates that 20 mA closes the valve. A 0 indicates that
20 mA opens the valve.
Alarm A
Active
PA1 L110 0
See Control Alarm Mode (B335) for PA1 states assigned
to alarm modes 0 - 6.
Alarm B
Active
PA2 L111 0
See Control Alarm Mode (B335) for PA2 states assigned
to alarm modes 0 - 6.
Auto Switch
SWA L112 0
This logic bit indicates the state of the A/M pushbutton
setting. It is a 1 if in auto and a 0 if in manual.
Remote
Switch
SWR L113 0
This logic bit indicates the state of the R/L pushbutton
setting. It is a 1 if in R and a 0 if in local.
Auto Enable
AE L114 1
When a 1, this logic bit permits auto control based on the
state of the Auto Switch (L112).
Remote
Enable
RE L115 0
When a 1, this logic bit permits remote operation based
on the state of the Remote Switch (L113).
Manual
Fallback
Disable
MFD L120 0
Under normal operation, whenever the controller is
powered up, the Auto/Manual Selector is forced to the
Manual position. When this datapoint is set to a 1, the
selector will not be forced to the Manual position at power
up, but will remain in the last position before power was
removed.
Datalink
No Parity
CP L256 0
This datapoint indicates if Datalink parity generation and
checking should be turned on or off. It is set to 0 for even
parity serial byte protocol. It is set to 1 for no parity
protocol.
Datalink
Disable
DLD L257 0
When set to 0, it permits full Datalink communication
capabililties. When set to 1, it disables Datalink
communication capabilities.
Table C-2. Database (Continued)
Title Symbol Datapoint Default Attribute
- INSTRUCTION MANUAL 1
- MicroMod Automation, Inc 2
- TABLE OF CONTENTS 3
- LIST OF FIGURES 6
- LIST OF TABLES 7
- 1.0 Introduction 9
- Introduction 3 11
- 1.2 Model Number Breakdown 12
- 1.3 Specifications 13
- 2.0 Installation 17
- Installation 11 19
- Figure 2-3. Intercase Spacing 20
- 2.4 Connections 21
- 2.5 Grounding 23
- 16 Installation 24
- Installation 17 25
- 18 Installation 26
- 3.0 Front Panel 27
- Front Panel 21 29
- Figure 3-6. Alarm Overlay 30
- 3.3 Front Panel Pushbuttons 31
- 24 Front Panel 32
- 3.3.1 Displaying a Datapoint 36
- 3.3.2 Altering a Datapoint 37
- ∆ = space 38
- 3.3.3 Defaulting the Database 39
- Figure 3-14. The KEY? Prompt 42
- Front Panel 35 43
- C & H 45
- A & Q 45
- TRL-C aborts the operation 46
- 40 Front Panel 48
- 4.0 Configuration Parameters 49
- Figure 4-1. ANIO/1 53
- Figure 4-2 53
- Figure 4-3. CCI0 55
- Figure 4-4. CCO0 55
- CCO L024 0 56
- OINV L288 0 56
- COTAG A280 CCO0 56
- AIX ■ ● ▲ ◆ B335 1 57
- RSW ■ ● ▲ ◆ L106 1 57
- Table 4-11. System Module 61
- Table 5-8. System Module 71
- 6.0 Analog Backup Controller 73
- Table 6-1 75
- Table 6-8. System Module 81
- 7.0 Ratio (PID) Controller 83
- Table 7-1 85
- Table 7-7. System Module 91
- 8.0 Automatic/Manual Station 93
- Table 8-1 95
- Table 8-8. System Module 101
- 9.0 Parameter Display 103
- 96 Parameter Display 104
- 98 Parameter Display 106
- 10.0 Instrument Tuning 107
- 10.3 Derivative Action (TD) 108
- 10.4 Instrument Tuning 108
- 11.0 EASY-TUNE 111
- 11.3 EASY-TUNE Parameters 112
- 108 Easy-Tune 116
- 110 Easy-Tune 118
- 112 Easy-Tune 120
- 12.0 Maintenance 121
- 12.3 Calibration 122
- 12.5 Resetting the Controller 123
- 12.6 Parts List 124
- 12.7 Supplemental Information 124
- Maintenance 117 125
- 118 Maintenance 126
- Maintenance 119 127
- 120 Maintenance 128
- Appendix B: Communications 133
- B.1.1 Configuration 134
- B.1.2 Protocol 135
- B.1.3 Message Types 136
- B 200H 1 138
- L 500H 1 Bit 138
- C 600H 3 138
- Appendix C: Database 141
- Table C-2. Database 142
- CIZ B264 144
- AIX B335 1 145
- ANO0 C000 0 145
- PV C100 0 145
- P or DOWN arrow pushbuttons 146
- 142 Database 150
Relacionado con productos y manuales para Equipo Micromod Micro-DCI: 53SL5100A Single Loop Controller
(180 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.062 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales